Welcome to Black Smith Products ::
Product Search
RC HELP & ADVICE

RC ACCESSORIES
Batteries/Chargers

Body Covers

RC Accessories

Engine

Engine Starters

Exhausts

Fixtures

Motors + Heatsinks

RC (electrics)

Spares / Upgrades

Tools

Wheels and Tyres

Information

Whats New?




Bookmark this site!







Home » Light Kits

 Checkout
L-001 1/10 Scale Body Shell Direct Roof Mount RC Police Light Bar LED
L-001 1/10 Scale Body Shell Direct Roof Mount RC Police Light Bar LED
To suit 1/10 scale model car or truck shells. This is a direct roof mount, so will need a few holes drilled in the center roof of your shell plus one larger hole directly in the middle of the bar for the wires to feed through. This is powered by a 9v battery (not included). This is the recommended input. 9 flashing models controlled by the switches pictured. Colour of the leds are red and blue. Light cover measures 113.9mm long x 24.22mm wide.
:
Price: £7.99
Out of Stock
L-002G 1/10 Scale Wheel Hub LED Lights M12 12mm Hex x 4 Green HUBS Only
L-002G 1/10 Scale Wheel Hub LED Lights M12 12mm Hex x 4 Green HUBS Only
To suit 1/10 scale models wheel hubs. As the wheel spins these light up giving off a brilliant green glow effect on your wheels. Great for 1/10 car wheels.These will not fit all wheels and only a select few. Essential you check measurements before ordering.These would replace a 12mm hub. Then the wheel goes on top of this and then wheel nut etc. Note no hub pins are included. To ensure a fit please check the thickness of the hub cut out on your wheel is no greater than 2mm measured from a flat of the hex to the outer wall edge. If so these will not fit. If less then this these will be ok. The outer hub wall of your wheel would fit into the recess on these 12mm hub/discs.When the wheel is spinning these will light up automatically to avoid battery drain its recommended to remove these after use. Their is no switch to turn them on / off.Batteries included however have a low 'mah' so would recommend purchasing more when ordering this item. We dont stock the correct battery however available through other sellers on ebay or any good hardware/watch store. Battery part number needed AG1 (button cells). Each wheel uses 2 so your looking for 8 in total.
:
Price: £7.99
Out of Stock


L-002M 1/10 Scale Wheel Hub LED Lights M12 12mm Hex x 4 Mix HUBS Only
L-002M 1/10 Scale Wheel Hub LED Lights M12 12mm Hex x 4 Mix HUBS Only
To suit 1/10 scale models wheel hubs. As the wheel spins these light up giving off a brilliant green glow effect on your wheels. Great for 1/10 car wheels.These will not fit all wheels and only a select few. Essential you check measurements before ordering.These would replace a 12mm hub. Then the wheel goes on top of this and then wheel nut etc. Note no hub pins are included. To ensure a fit please check the thickness of the hub cut out on your wheel is no greater than 2mm measured from a flat of the hex to the outer wall edge. If so these will not fit. If less then this these will be ok. The outer hub wall of your wheel would fit into the recess on these 12mm hub/discs.When the wheel is spinning these will light up automatically to avoid battery drain its recommended to remove these after use. Their is no switch to turn them on / off.Batteries included however have a low 'mah' so would recommend purchasing more when ordering this item. We dont stock the correct battery however available through other sellers on ebay or any good hardware/watch store. Battery part number needed AG1 (button cells). Each wheel uses 2 so your looking for 8 in total.
:
Price: £7.99
Out of Stock
L-003 1/10 Scale Racing Car 12 LED Light Kit Throttle Brake Set
L-003 1/10 Scale Racing Car 12 LED Light Kit Throttle Brake Set
12 LED Light Set. To suit 1/10 scale models car or truck shells. Lights react to receiver signals so for example if braking the rear red leds will show (depending on how you set it up). Total of 12 LEDs recommend using light buckets (not included). This set would be powered by the receiver (any 27mhz / 35mhz / / 40mhz AM/FM or 2.4ghz) which must be running by an esc or have a 6v DC input if using two servos for nitro models. Note: Servo and receiver pictured not included.
:
Price: £12.99


L-004 1/10 Scale Body Shell Direct Roof Mount RC Police Light Bar LED Rotational
L-004 1/10 Scale Body Shell Direct Roof Mount RC Police Light Bar LED Rotational
To suit 1/10 scale model car or truck shells. This is a direct roof mount so will need a few holes drilled in the center roof of your shell plus one larger hole for the wires to feed through. This is powered by either a direct 6v input (no batteries included) or by a spare port on your receiver. The connector type is male JR. Note: Input by a voltage higher than 6v DC will damage the unit. Light bar measures 68mm x 13mm between fixing points (rectangle). A 10mm hole is required on each side between the fixing points for the wire to feed through. Simple 1 page instructions included to help with fitting.
:
Price: £9.99
Out of Stock
 

« Previous | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | »

*By Ordering with BlackSmithProducts LTD. You automatically agree to our terms and conditions.
*When ordering a run in nitro model, the terms and conditions on warranty will change,
please make sure you have read these changes…
*All pictures and text on our website is Copyright © BlackSmithProducts LTD.




Telephone: +44 (0) 1293 863 411 - Email: info@blacksmithproducts.co.uk
We accept Delta
We accept Visa Electron
We accept Maestro
We accept Mastercard
We accept Solo
We accept Switch
We accept Visa
Copyright © Black Smith Products. All rights reserved. Protected by copyright law protection act.